Thảo luận về N80

tin vui nè có thể update FW N80 online rồi đấy. mình vừa up thành công một chú n80thawanhf n80i rùi. download 73mb liền. lâu nhưng đã lém.

Flashing BB5 Nokia phones with an USB cable​

(Update of 08/2006)​

This tutorial explains how to upgrade your Nokia BB5 with the latest firmware. You will need a USB cable (DKU-2/DKE-2/CA-53 . . .) and the software “PHOENIX Service” by Nokia! (No dongle to buy!!!)

This method proved successful by flashing one Nokia 6680 ORANGE and another one branded SFR, and also on other hundreds of BB5 phones, like 6630 Nokia original firmware version, 6280, N70, N90, N80. . .
However, we cannot be hold responsible for the damages you can do by making a wrong handle, and losing your warranty!

BEFORE BEGINNING!

- Save all the data from your phone (on your memory card or on PC)
- Remove your memory card and your SIM card
- Fully charges your phone’s battery
- Uninstall Nokia connectivity cable driver / Nokia connectivity solution from your PC!
- Uninstall Diego and Phoenix if you have them on your PC (think to delete manually from « program files » the files that might persist after the uninstall, and even clean tour registries if you still have problems with CCleaner) then reboot

what you need:

- the following software:


1 - Diego
2 - Phoenix 2004 + cr++k
3 - Phoenix 2006 (part 1 + part 2) + cr++k

- The firmware of your phone. (Check the file ‘last firmware’ for the latest versions of your bb5 phone at the date of appearance of this tutorial)

- The DKU-2 cable and the phone, of course.

Some of these files are archived on volumes. Unpack them all in the same folder and you will finally get the file you want. For Phoenix 2004, do “Save as” in order to download it, and change it in “.EXE”.



Step N° 1 - INSTALL DIEGO

- Run and install the following file: Nokia Diego 3.07 Sp2.msi

- If you get an error during the installation, it’s because you didn’t uninstall the Nokia connectivity cable driver!



Step N° 2 - INSTALL PHOENIX SERVICE 2004 WITH THE CR++K

- Open the crk first. Just open it, don’t run it now!

- Start installing phoenix 2004. During the installation you’ll get an error message.

- Press on “Retry” and run the cr++k immediately after! (Check that the destination folder is Windows/system32).

If you’re not fast enough, the message will reappear and you’ll have to re-run the cr++k the same way as above (but faster…)

- You’ll get 2 error messages, just press OK, and then Finish.

- You successfully installed phoenix service 2004.


Restart your PC.


Step N° 3 - INSTALL PHOENIX 2006

You have the shortcut for Phoenix on your desktop. Run it, and you might get several times the message "dskey not found!”. This is normal, just press « ok », and eventually Phoenix should open.

- Don’t close the program. You must only minimize the window.

- Run phoenix_service_sw_2006_20_9_148.exe. You shouldn’t have any error!

- Make sure you don’t restart the PC at the end of the installation. Just choose "restart my PC later" and then Finish.

Now you can close the window of Phoenix that you have minimized.

Restart your PC.If you have any error messages, just press « Cancel ».

Run the crk of Phoenix 2006. (Check that the destination folder is Program files/Nokia/phoenix)

You can now run Phoenix 2006. If asked for login, just enter some crap.

Step N° 4 – INSTALL THE CABLE

it is advisable to close the applications you don’t need during the flashing (like antivirus, anti-spy ware etc).

Connect your USB cable (DKU2 or another) to the PC, and connect your started phone.

Wait for Windows XP to install all the drivers (it’s better to not have unknown hardware devices), and then don’t touch your phone anymore because the cable doesn’t hang on very well and it might disconnect!

Now you have to execute these steps in phoenix:

File / Manage connection / New/ select USB / press Finish / Apply and Close.


Normally your phone will be identify if not Scan Product" from the File menu Go to menu file /scan procduct



Step N° 5 - FLASHING THE PHONE


- Put the firmware folder on your desktop. (e.g. RM36 for a Nokia 6680)
It should contain 2 files (this might vary depending on your phone model and download source):
One (MCU) with the .COR extension and the other one (PPM) with the .V30 extension.

- Do the following in phoenix: Flashing / sw update
you should see the name of the firmware folder (like RM36) on the top of the phoenix window. If you can see it, you’re on the good way.

- On the first line (Image File), browse for your file that ends by .COR.
- On the second line (PPM File), browse for your file that ends by .V30.


Press START and don’t touch your phone anymore.

Wait for a message!
Phoenix will tell you to press the ON key of your phone and OK on the Phoenix software!

Firmware upgrade was done!


Notes:
For some phones, you don’t have to install phoenix 2006. The 2005 or 2004 might be enough:
Phoenix 2004 --- 6630 . . .
Phoenix 2005 --- N70 . . . 6680 . . . 6630
Phoenix 2006 --- N90 . . . N70 . . . 6680 . . . 6630 . . .

You will have the list of the supported models for each version, when you make “File / open product”.

If you have trouble with the phone’s drivers, you can install Nokia_Conn_Cable_Driver_159_ita.msi or even re-install Nokia PC Suite).

If you uninstall “Nokia connectivity” at the beginning, you can re-use Nokia PC Suite after that.

If step 3 doesn’t work, u can try the old solution :Step N° 3 - INSTALL PHOENIX 2006
You have the shortcut for Phoenix on your desktop. Run it, and you might get several times the message "dskey not found!”. This is normal, just press « ok », and eventually Phoenix should open.
- Don’t close the program. You must only minimize the window.
- Run phoenix_service_sw_2006_12_5_136.EXE. You shouldn’t have any error!
- Make sure you don’t restart the PC at the end of the installation. Just choose "restart my PC later" and then Finish.
Now you can close the window of Phoenix that you have minimized.
Go to the folder Program files/Nokia/phoenix and copy this entire folder on your desktop.
Restart your PC.
If you have any error messages after the reboot, just press « Cancel ».
Go to /Program files/Nokia/, delete the folder phoenix, then replace it by the folder that you saved on your desktop. Now Re-run the crk of Phoenix 2004.
You can now run Phoenix 2006

The reference of the language pack helps you to choose the language you want in your phone (so you can pick a different version than the .V30).

The phones that are locked on an operator will remain so after the flashing. The unlock code provided by your operator will work whether you flash your phone in a Nokia original firmware version or not.

The number of FW files is depending on the phone model (6630 has 2 files / 6020 has 3 files / Communicator has 5 files). The ideal would be to have a flash .EXE (data package), allowing to know the order of the files due to the included “.INI”; but there’s not always the case (the minimum is to have one mcu and one ppm).

The order in the flashing procedure (see the JPG image)

Image file: \products\rh12_28_11005.500 (.3 chiffres)
PPM file: \products\ rh12_28_11005.50c (.2 chiffres + lettre)
Content file: \products\rh12_28_11005.50.ucp_c (.2 chiffres+ mot + lettre)
ADSP Flash : NONE (communicator)
APE Variant : NONE (communicator)
APE Userdisk: NONE (communicator)

For dead phones: File/ Open product, choose your phone model and then flash it (see attached PDF). If it doesn’t work, you can still flash your phone with a box, after have been doing a full-erase.

A big THANK YOU to all the people that contributed to this tutorial and to those that translated it (Fr, Ar, Eng, It, Ger), so that many people can take advantage of it J

You làm có đúng là N80i ko đó

N80i là gì?Internet hay là itune như mọi người vẫn đang đồn?FW của nó là gì?Cho kí hiệu xem cái

Là Internet đó bạn có thêm rất nhiều thứ dowload các file này đọc sẽ hiểu nè
http://nds1.nokia.com/files/support/apac/phones/guides/Nokia_N80_APAC_UG_vi.pdf
http://nds1.nokia.com/files/support/apac/phones/guides/Nokia_N80IE_APAC_QSG_vi.pdf
http://nds1.nokia.com/files/support/apac/phones/guides/Nokia_N80IE_APAC_APP_vn_vi.pdf

Up FW N80 lên N80i ?????

Bác up thế nào? Có phải đổi code không và up online luôn hay phải down về up ofline? Hướng dẫn cho ae với, nhưng phải đúng là lên N80i nhé. Thanks.

up offline đó bác, tới bi giờ Nokia vẫn chưa hỗ trợ up online cho N80i đâu.

Tin vui cho bạn nào không to gan..
để up lên FW n80i, có thể đem ra care, nó up lên cho, kô cần change code..
lúc trước mình tự làm, product code thay dổi, ko còn là RM 92(12) nữa mà thành RM 92 (......xxx) nhưng sau khi đem vô care, nó up lại vẫn là FW đó nhưng đưa về RM 92(12)
hehe

CHO DÙ NÓ LÀ INTERNET HAY ITUNE THÌ NÓ CỦNG CHỈ KHÁC CON N80 THƯỜNG VỀ FILMWARE THÔI
GIỐNG NHƯ CON N73 VÀ N73ME DẠO NAY NOKIA BIẾT CÁCH LÀM TIỀN GHÊ
CHỈ THAY ĐỔI CÓ CÁI PHẦN MỀM CÁI VỎ VÀ CÁI THẺ THÌ ĐẢ CÓ 1 SẢN PHẨM MỚI.CHỈ TỔ TỘI CHO NHỬNG AI CÓ TÍNH HAY THAY ĐỔI ĐIỆN THOẠI