Hướng dẫn Update Firmware/flash deadphone bằng Phoenix 2011 (update 27/5/2011)

đường dẫn chính xác là đây C:\Program Files\Common Files\Nokia\DataPackage\Products nếu file firm là file exe thì nó sẽ cài thẳng vào đấy còn nếu là file zip thì copy vào đấy nhé

Chủ thớt ơi cho hỏi chút
Mình dùng 5800 FW v51 ( cái này up tự động ~~ )
h mình muốn chuyển sang CFW 9 Omnia Homescreens | 5800 v51.0.006 CFW by Anther thì dùng Phoenix đc ko
nếu đc thì làm theo hướng dẫn bài 1 à ><

hic cứu em với.
Em vừa cài xong nhưng khi khởi động máy nó lại báo như sau: "Phone start up failed. Contact the railer". Mong các sư phụ chỉ giúp em với

Cho hỏi cái này. Nghe nói là hack E72 bằng cách chạy firmware này được luôn phải kg vậy. Nếu được làm ơn hướng dẫn cụ thể với nhe.

Phoenix Service Software 2010.24.008.43820 Cra_cked (29/09/2010)

Mã:

Main component versions in the release: 
• DK2 Driver Version 07.14.0.25 
• Nokia Connectivity Cable USB Driver Version 7.1.31.0 
• Flash Update Package 10.34.1.3 
• FLS-x Drivers Version 2.09.28 

1. Main changes & error corrections from previous version

New Products added 
• RM-640, RM-662, RX-90

New features: 
• New version of Autotuning and RF Losses  
• New version of Flash Update Package 
• New versions of Product and Instrument API

Error Corrections & changes 
• RF Autotuning improvements for RM-497 and products using same engine enablingull repair service concept support for RM-497 
• Improvements for ALS Calibration 
• improvements to WLAN Size 4 TX tuning 
• Improvements to CU-4 voltage settings 
• Improvements to EM calibrations and CU-4 voltage handling 
• Flashing improvements to dead phone flashing 
• Improvements to label printing 

Corrections to Genius cases # 158703, #156736, #160883, #160361, #162759, #159362, #160796, #156018, #157265 

2. Known errors & limitations  
• Software downgrade with Tucson system is only possible for BB 5.0 products supporting the Data Package 2 concept. 
• Flashing with setup FLS-5, SS-46 and product specific adapter is not  supported anymore. FLS-5 is supported with phone specific cables only. 
• If you install old DCT-4 data packages, Flash Update Package File  installation path may be wrong. This is caused by very old DCT-4 data  packages which contain Flash Update Package and overwrite current  information during installation. If you experience problems when  updating FPS-x prommers, please check that Phoenix “Prommer maintenance”  is looking for the files from the correct location which is “C:\Program  Files\Common Files\Nokia\Tss\Flash”. If not, Phoenix will show error  “Update via ini – file failed”. In this case, select “Update” from that  Phoenix “Prommer maintenance” – UI, browse to correct directory and  select “fpsxupd.ini” for all other prommers except the FPS-8. 
• Refurbishment flashing and product code change for RX-51 product requires SX-4 card to be available 
• FPS-21 flashing for RX-51 works only with TCPIP connection. FPS-21  prommer with new HW version is needed to correct this, and it is  estimated to be available by the end of 2010. 
• Please refer to product specific documents and instructions concerning the limitations of the RX-51 product 
• RX-51 flashing does not work when CU-4 is used 
• When version 2010_12_8_42304 or newer with FUSE connection manager is  installed on top of older Phoenix versions, there may be an additional  delay of several minutes when you start Phoenix for the first time.  Please wait patiently; Phoenix will start after configuration is  finished. 
• When using Data Package download functions with online  connection, download times may occasionally be long. This is not caused  by Phoenix (or Care Suite). The download speed from online servers is  occasionally is known to be slow, depending on how data is buffered on  caching servers. 
• Note concerning the installation and use with Administrator and User rights
-  If you install Phoenix, start Phoenix and configure connections from  FUSE connection manager as Administrator, you may not be able to start  Phoenix after you log off and try to use Phoenix with User Rights  afterwards 
• If you experience the above mentioned problem: 
- Log on as Administrator 
- Deleted Fuse folder and its contents from: C:\Documents and Settings\All Users\Application Data\Nokia\ 
- After this Fuse’s connection list will be empty and it can be used directly with guest/admin rights. 
- This has to be done only once. 
• After you close Phoenix, it may not restart. To rectify this: 
- Use Windows Task Manager to manually shut down phoenix.exe and FuseService.exe processes, or optionally restart your PC 
• Mass memory content file flashing does not work for all products over USB – FPS-10 or FPS-21 Flash Prommer must be used!

Please  use only one connection for one Flash Prommer ( USB or TCPIP ). If both  USB and TCPIP connection are configured to same Flash prommer, FUSE  will be unstable.  

Supported operating systems and user rights 
• Windows XP Service Pack 1 or higher 
• When installing Phoenix into Win XP you must have local admin rights. 
• When using in Win XP, user must have power user rights.

Download:

Mã:

http://rapidshare.com/files/421995488/Phoenix_Service_Software_2010.24.008.43820_EN.rar

Tóm lại là copy RM-xx vào C:\PF\nokia\phoenix\products hay là vào C:\Pf\Common Files\Nokia\DataPackage\Products nhỉ, sao mà lộn xộn quá. Lúc mình tải fw bằng navifirm thì nó gồm có 10 files, có phải mình phải chép nó vào thư mục RM-xx của mình rồi chép vào 1 trong 2 đường dẫn trên hay không, các bác làm ơn nói rõ ràng giùm e với

Chính xác là đặt thư mục RM-xx như vị trí đầu tiên bạn nói.

Nếu như vậy thì bạn nào đó nói đến thư mục C:\pf\Common files\nokia\datapackage\products là có ý nghĩa j ko

Là nơi chứa thư mục RM-xxx sau khi Install Firmware Full bạn ạ.